General requirements for installation of solar panel

By Bharat Ribadiya -
Solar power is free, you didn't have to pay for it and if you want to install solar panels at your home or office then the following things are required for it.

1-Solar Panel
2-Charge Controller
3-Battery
4-Inverter

These all are the general requirements for installing solar panel. lets know about it in briefly.

(1) Solar Panel


Solar panel are available in 12V, 24V, 36V etc. As per your requirements choose a solar panel. A 12V, 5A and 60W will provide you 12V DC voltage and this voltage is stored in battery. But you have to connect the charge controller between solar panel and battery.

(2) Charge Controller

This is 5-10 Ampere Charge Controller, It is control the current or /and voltage regulator to keep batteries from overheating. Sometimes the 12V solar panel output is 16V to 20V, so if their is not any protection or regulation of voltage then batteries will damage.

-Do you always need charge controller?
-Why 12V panels gives 17V?
-Charge controller types and much more about controller.

 (3) Battery


Batteries are used to storage the voltage which produce by solar panels. There are various types of batteries available. To Know more about lifespan, selection, size codes, Amp-hour visit this. Read More

(4)Inverter
There are many types, sizes, brands, and models of inverter are available. Choosing an inverter can be difficult. You have to consider many factors while selecting the inverter. Read More

Popular posts from this blog

How to control One Lamp from three/six different places and working principle of intermediate switch?

By Bharat Ribadiya -
Image
In this article we learn about how to control a lamp with 3 different switches at different places. This is very useful. For doing this we required two 2-way switch, 1 intermediate switch and a lamp. Connect all these as shown as in the below diagram. Fig.-1 In the above diagram the lamp is on because the circuit is in closed condition.To understand easily the circuit diagram for this, is given below.  Fig.-2 In this case the lamp(bulb) is in off condition. So, the circuit is open condition. Here, one more example is given.  How you can turn on/off a lamp or bulb from six different places. For this we required four number of intermediate switch, two number of 2 way SPDT switch and 1 bulb. Connect all these components as shown as in the figure below. Fig.-3 What is Intermediate switch , its construction and working principle? Fig.-4 An intermediate switch have four terminals. Because of this terminals it is possible to change the flow of the current fro
Read more

Three phase electrical wiring system for home & multi-floor building

By Bharat Ribadiya -
Image
In this article you will learn about how to do three phase wiring in home. Generally, the elctrical supply provider company install single phase energy meter for where requirements is 7.5 kW load in domestic areas but if this limit exceeded then they install 3-phase meter. For this we required following things. Requirements- Required Materials Number Three phase energy meter 1 Three pole, 63 A, MCCB 1 Double pole, 63 A, 30 mA, Trip current RCD 3 Double Pole MCBs, 63A 3 Single Pole, 20A, MCB 6 Single Pole, 16A, MCB 3 Single Pole, 10A, MCB 6 Distribution board cases 3 Cupper strips for MCB Common connection 3 Here, the connected load is single phase. their is no 3 phase load connected to the 3 phase system. The 3 phase wiring are used because our load is more then 7.5 kW. Now, let's start the procedure how to install 3 phase wiring for your home. Figure 1- 3 phase winding in home As shown in the
Read more

Automatic and manual UPS system wiring for home or office with circuit diagram

By Bharat Ribadiya -
Image
Automatic UPS system wiring for home or office This article is about how to connect a UPS system in our home or office and this is very useful information.  The below circuit diagram shows the how to connect a UPS from our main supply to appliance(load). This circuit diagram is for in case of falling the main power supply and you want to supply power to specific appliances, TV, AC, laptop etc. in your home or office.  As shown as, two rooms are connected with main power supply.  Here, you don't have to connect the neutral wire connection from UPS because it's already connected the phase and neutral wire from the main power supply with the same point. To connect UPS first you have to remove the connection of phase wire from the main distribution box(from SP,DP or CB) of those rooms which you want to connect with UPS. By doing this(connect with both supply), we can use the power without interruption. If main power fails the UPS will provides the power to the
Read more